Wymiary produktu | 23 x 10 x 10 cm; 930 g |
---|---|
Numer części | 08223-20 |
Wysokość wyświetlacza | 10 cm |
Rodzaj materiału | Tworzywo sztuczne |
Głośność | 1 Nieznany modyfikator |
Rodzaj źródła zasilania | Obsługa ręczna |
Producent | Gardena Deutschland GmbH - DE Parent |
Numer modelu | 08223-20 |
ASIN | B07YSTLS8P |
Bezpłatny okres próbny Amazon Prime
Nielimitowana dostawa Premium jest dostępna dla członków Amazon Prime. Aby dołączyć, wybierz Tak, chcę skorzystać z BEZPŁATNEJ dostawy na następny dzień dzięki bezpłatnemu okresowi próbnemu Amazon Prime nad przyciskiem Dodaj do koszyka i potwierdź swoją subskrypcję bezpłatnego okresu próbnego Amazon Prime podczas finalizacji zakupu.
Korzyści klientów Amazon Prime:- Dostawa na następny dzień bez ograniczeń
- Nagradzane filmy i seriale, w tym oryginalne produkcje Amazon, wszystko to co lubisz na swoim ulubionym urządzeniu.
- Ekskluzywne okazje dla członków Amazon Prime, w tym wczesny dostęp do niektórych okazje
Ważne: Twoja karta kredytowa lub debetowa NIE zostanie obciążona po rozpoczęciu bezpłatnego okresu próbnego lub w przypadku anulowania w trakcie okresu próbnego. Jeśli Amazon Prime jest właśnie dla Ciebie, nie musisz nic robić. Po zakończeniu bezpłatnego okresu próbnego zostanie naliczona opłata w wysokości 49 zł/rok za członkostwo Prime (miesięcznie).
Dodaj inne przedmioty:
Gardena wynurzalny zraszacz wahadłowy OS 140: System nawadniania do kwadratowych i prostokątnych powierzchni do maks. 140 m², montowany na poziomie gruntu (8223-20)
Zachowaj przedmiot w oryginalnym stanie, z zewnętrznym pudełkiem marki, dołączonymi etykietami, instrukcją obsługi, kartami gwarancyjnymi i oryginalnymi akcesoriami w opakowaniu producenta w celu pomyślnego opracowania zwrotu.
Możemy skontaktować się z Tobą w celu ustalenia uszkodzenia lub wady produktu przed wydaniem zwrotu/wymiany.
Dowiedz się więcej o naszych zasadach dotyczących zwrotów.
Opcje zakupu i dodatki
Marka | Gardena |
Kolor | Wielokolorowy |
Materiał | Tworzywo sztuczne |
Styl | Zraszacz wpuszczany czworokątny |
Wymiary elementu dł. x szer. x wys | 23 x 10 x 10 cm |
Informacje o tym produkcie
- Idealny do prostokątnych powierzchni: pozwala łatwo i wygodnie nawodnić kwadratowe lub prostokątne powierzchnie od 2 m² do 140 m², nadaje się zwłaszcza do małych i wąskich trawników
- Równomierne podlewanie: 16 elastycznych, precyzyjnych dysz z miękkiego tworzywa sztucznego zapewnia wyjątkowo równomierne rozdzielanie wody i bezusterkową pracę
- Łatwa instalacja: wygodne wbudowanie i wygodne podlewanie. Dzięki zainstalowaniu w rurociągu zaworu odwadniającego system jest zabezpieczony przed zamarznięciem
- Możliwość sterowania: poprzez regulację ilości można precyzyjnego określić obszar, który ma być nawadniany
- W zestawie: 1x Gardena wynurzalny zraszacz wahadłowy OS 140
Szczegóły dotyczące zgodności produktu z przepisami
Zobacz szczegóły dotyczące zgodności tego produktu(podmiot odpowiedzialny w UE).
Często kupowane razem
Klienci, którzy oglądali ten produkt, oglądali również
Od producenta
Wynurzalny zraszacz wahadłowy GARDENA OS 140
Stałe nawadnianie kwadratowych i prostokątnych powierzchni
Wynurzalny zraszacz wahadłowy GARDENA OS 140 to idealne rozwiązanie – na stałe zainstalowane pod ziemią – do podlewania kwadratowych i prostokątnych trawników o powierzchni od 2 do 140 m². Za pomocą rur montażowych zraszacze łączy się w system GARDENA Sprinklersystem, do którego można też włączyć turbinowe wynurzalne zraszacze wahadłowe GARDENA T 100, T 200 lub T 380. Wynurzalny zraszacz wahadłowy GARDENA OS 140 ma gwint wewnętrzny 3/4’’.
Dane techniczne
- Min. zraszana powierzchnia: 2 m²
- Min. zraszana powierzchnia: 140 m²
- Zasięg: 2 m - 15 m
- Gwint: 3/4" gwint wewnętrzny
|
|
|
---|---|---|
Praktyczny przyprostokątnych powierzchniachSzerokość zraszania urządzenia OS 140 można zmieniać w zakresie od 1 m do 9,5 m, zasięg wyrzutu m od 2 m do 15 m. Natężenie przepływu wody reguluje się bezstopniowo. Zmienne ustawienia umożliwiają zastosowanie nawet na niewielkich powierzchniach i w ciasnych częściach ogrodów. |
Trwała instalacjaProsty montaż i wygodne podlewanie. Instalację przed zamarznięciem zabezpiecza zawór odwadniający (nr art. 2760), zainstalowany w ciągu rur (zawór nie jest objęty dostawą). |
Równomierne nawodnienie16 elastycznych, precyzyjnych dysz z miękkiego tworzywa sztucznego zapewnia równomierne rozdzielanie wody, a drobnooczkowy filtr zanieczyszczeń gwarantuje bezusterkową pracę. |
Przewodniki i dokumenty dotyczące produktów
Informacje o produkcie
Szczegóły techniczne
Informacje dodatkowe
Baterie: | 1 Nieznany |
---|---|
Data pierwszej dostępności | 30 sierpnia 2019 |
Oceny klientów |
4,5 z 5 gwiazdek |
Ranking najlepiej sprzedających się produktów | Pozycja 600 w kategorii Ogród (Zobacz Top 100 w kategorii Ogród) Pozycja 9 w kategorii Zraszacze ogrodowe |
Opinia
Szukasz konkretnych informacji?
Od marki
-
Preferowana marka ogrodowa dla milionów właścicieli domów i ogrodów na całym świecie. GARDENA osiąga to dzięki oferowaniu pełnego asortymentu wszystkich produktów, zarówno w zakresie nawadniania, pielęgnacji trawników, pielęgnacji drzew i krzewów, jak i uprawy gleby.
Obecnie GARDENA jest wiodącą marką wysokiej jakości narzędzi ogrodniczych w Europie i jest reprezentowana w ponad 80 krajach na całym świecie.
-
-
-
-
-
Każda kropla się liczy
Woda jest cennym zasobem. GARDENA nawadniacze dostarczają roślinom odpowiednią ilość wody.
-
Dlaczego GARDENA?
Doskonała jakość i wysokie standardy sprawiły, że GARDENA jest liderem na rynku technologii ogrodniczych i nawadniających. Znajduje to również odzwierciedlenie w naszych produktach.
Jak uzyskać wsparcie?
W naszym centrum doradczym na stronie internetowej GARNDENA klienci mogą znaleźć wsparcie w zakresie planowania nawadniania, zakupu poszczególnych części oraz ewentualnych napraw.
Nasze zaangażowanie
GARDENA współpracuje między innymi z UNICEF-em i Forest Stewardship Council, aby wspierać zrównoważone projekty.
Opinie o produkcie
Recenzje klientów, w tym oceny produktu w postaci gwiazdek, pomagają klientom dowiedzieć się więcej o produkcie i zdecydować, czy jest dla nich odpowiedni.
Aby obliczyć ogólną ocenę w postaci gwiazdek i procentowy podział według gwiazdek, nie używamy prostej średniej. Zamiast tego nasz system bierze pod uwagę takie kwestie, jak aktualność recenzji i czy recenzent kupił produkt w serwisie Amazon. Analizuje również recenzje w celu zweryfikowania wiarygodności.
Dowiedz się więcej, jak działają opinie klientów w serwisie Amazon-
Najlepsze o produkcie
Najlepsza opinia o produkcie z Polski
Wystąpił problem podczas filtrowania opinii. Spróbuj ponownie później.
Najlepsze opinie o produkcie
Review written 6 months after installation.
3/4” female pipe thread on bottom.
+/- 28 PSI minimum to pop up.
Excellent design & built very well.
Bigger than you may think.
Not as much of an eyesore as you may think.
I bought 9 of these between two orders, which shipped to the US from Amazon UK and arrived a lot faster than estimated at checkout (about a week instead of three weeks). I’m very happy with the service.
These are great sprinkler heads and a lot more fun than the standard Rotors or Sprays normally installed for US homes. The coverage area is very large: about 50 feet forward and back by 30 feet side to side (at approx 40PSI operating pressure).
The width of the spray is adjustable and you can separately adjust left and right sides as needed, and it is easy to set forward and back limits. There is also a flow rate valve that adjusts the distance of the spray, though you would probably only lower this if your pressure was so high that the spray is turning into a mist.
The spray is a nice “light shower” emulating a gentle rain. It does take longer to properly saturate an area but it gives the lawn more time to absorb the water, so there’s little or no runoff.
These do not work very well on windy days because they have a rather tall spray, though they seem to do fine in a light breeze. I would also not recommend these sprinklers for odd shaped areas where the bordering space should not get wet since the pattern is square.
One of these can easily replace 3 or 4 Rotors, but keep in mind that one of these delivers only about 3.5 gallons per minute over that same area, so watering times will need to be longer per zone. That said you can install fewer zones with each one covering a larger area.
You might be surprised when you first see these sprinkler heads: they are rather large compared to others.
In one part of my system I installed three OS140 sprinklers on a single zone where previously there were 12 Rotors split between two zones in the same area, and it turns out that I could have used only two for that area. Three did turn out to be better because I was able to reduce the watering time a little bit by shortening the forward and back distances on all three so there was no “head to head” watering coverage, resulting in more “passes” over each sprinkler’s area.
About “head to head” spacing: these sprinklers work best in the middle of an area, with no overlap between sprinkler heads. The only real benefit of head to head coverage with these sprinklers is a reduced watering time. If you do decide to use head to head coverage you should consider putting the edge sprinklers on a separate zone so their watering time can be reduced by half to prevent overwatering. Some Smart controllers (the Yardian Pro) can run two zones at once, so you could start with center heads and edge heads (if pressure permits) and have the edge zone turn off halfway through the cycle.
The design of the OS140 is an improvement over previous models that had a flip up lid and a more limited range of oscillation. The head of the new design sits neatly in a slot in the lid, and the lid can be removed and replaced at any angle, making it easy to fine tune the position of the of the head.
The head can be removed without any tools by simply unscrewing it counter-clockwise. This gives you quick access to the filter for cleaning when needed. The spring mechanism remains in the bottom, secured by its own raised collar, and can also be removed if service is needed.
The lower part of the body has a bunch of fins, or ribs, that firmly secure the sprinkler in the ground. My lawn guy has run over them many times and they haven’t budge or tilted, even when the ground was still soggy after a storm.
The pipe connection is a female 3/4” NPT standard located at the bottom. For my installation I used a 90 degree threaded/glued elbow and connected directly to the laterals with PVC.
These were installed in sandy soil by digging a 14” diameter hole, about 12” deep, and then seating the sprinklers in about 3” of pea gravel and fine sand up to the second fin/rib (mostly underneath the head to protect the pipe). The rest of the hole was filled in with the removed soil, tightly packing the dirt into the remain fins/ribs.
Once the head is installed you really cannot turn the sprinkler body, but it is very easy to position the spray head to face the right direction by turning clockwise (you really can’t over tighten the threads since the pop up mechanism is designed to turn clockwise once the head is firmly screwed in).
Overall I am very happy with this product, and my friends and neighbors are really impressed how well they work and pretty they are to watch. It’s like adding “dancing fountains” to my yard.
If only they lit up at night: a strip of LEDs across the head powered by a little water turbine, perhaps?
Opinia napisana w Stanach Zjednoczonych dnia 4 kwietnia 2024
Review written 6 months after installation.
3/4” female pipe thread on bottom.
+/- 28 PSI minimum to pop up.
Excellent design & built very well.
Bigger than you may think.
Not as much of an eyesore as you may think.
I bought 9 of these between two orders, which shipped to the US from Amazon UK and arrived a lot faster than estimated at checkout (about a week instead of three weeks). I’m very happy with the service.
These are great sprinkler heads and a lot more fun than the standard Rotors or Sprays normally installed for US homes. The coverage area is very large: about 50 feet forward and back by 30 feet side to side (at approx 40PSI operating pressure).
The width of the spray is adjustable and you can separately adjust left and right sides as needed, and it is easy to set forward and back limits. There is also a flow rate valve that adjusts the distance of the spray, though you would probably only lower this if your pressure was so high that the spray is turning into a mist.
The spray is a nice “light shower” emulating a gentle rain. It does take longer to properly saturate an area but it gives the lawn more time to absorb the water, so there’s little or no runoff.
These do not work very well on windy days because they have a rather tall spray, though they seem to do fine in a light breeze. I would also not recommend these sprinklers for odd shaped areas where the bordering space should not get wet since the pattern is square.
One of these can easily replace 3 or 4 Rotors, but keep in mind that one of these delivers only about 3.5 gallons per minute over that same area, so watering times will need to be longer per zone. That said you can install fewer zones with each one covering a larger area.
You might be surprised when you first see these sprinkler heads: they are rather large compared to others.
In one part of my system I installed three OS140 sprinklers on a single zone where previously there were 12 Rotors split between two zones in the same area, and it turns out that I could have used only two for that area. Three did turn out to be better because I was able to reduce the watering time a little bit by shortening the forward and back distances on all three so there was no “head to head” watering coverage, resulting in more “passes” over each sprinkler’s area.
About “head to head” spacing: these sprinklers work best in the middle of an area, with no overlap between sprinkler heads. The only real benefit of head to head coverage with these sprinklers is a reduced watering time. If you do decide to use head to head coverage you should consider putting the edge sprinklers on a separate zone so their watering time can be reduced by half to prevent overwatering. Some Smart controllers (the Yardian Pro) can run two zones at once, so you could start with center heads and edge heads (if pressure permits) and have the edge zone turn off halfway through the cycle.
The design of the OS140 is an improvement over previous models that had a flip up lid and a more limited range of oscillation. The head of the new design sits neatly in a slot in the lid, and the lid can be removed and replaced at any angle, making it easy to fine tune the position of the of the head.
The head can be removed without any tools by simply unscrewing it counter-clockwise. This gives you quick access to the filter for cleaning when needed. The spring mechanism remains in the bottom, secured by its own raised collar, and can also be removed if service is needed.
The lower part of the body has a bunch of fins, or ribs, that firmly secure the sprinkler in the ground. My lawn guy has run over them many times and they haven’t budge or tilted, even when the ground was still soggy after a storm.
The pipe connection is a female 3/4” NPT standard located at the bottom. For my installation I used a 90 degree threaded/glued elbow and connected directly to the laterals with PVC.
These were installed in sandy soil by digging a 14” diameter hole, about 12” deep, and then seating the sprinklers in about 3” of pea gravel and fine sand up to the second fin/rib (mostly underneath the head to protect the pipe). The rest of the hole was filled in with the removed soil, tightly packing the dirt into the remain fins/ribs.
Once the head is installed you really cannot turn the sprinkler body, but it is very easy to position the spray head to face the right direction by turning clockwise (you really can’t over tighten the threads since the pop up mechanism is designed to turn clockwise once the head is firmly screwed in).
Overall I am very happy with this product, and my friends and neighbors are really impressed how well they work and pretty they are to watch. It’s like adding “dancing fountains” to my yard.
If only they lit up at night: a strip of LEDs across the head powered by a little water turbine, perhaps?